Fluke 725 Multifunction Process Calibrator

Versatile troubleshooting tool Power transmitters during test using the loop supply with simultaneous mA measurement so you can test a transmitter out of circuit and better isolate problems. The 725 can also test a variety of fast pulsed RTD transmitters and PLCs (Programmable logic controllers), with pulses as short as 10 ms. Source mA with simultaneous pressure measurement to conduct valve and I/P (Input current/Output pressure) tests in a single device. You can also test flow meters with frequency and CPM (counts per minute) functions and perform fast linearity tests with auto-step and auto-ramp features so you can quickly verify the mA signal at different output levels. For more precision, pulse sourcing, pulse counting (totalizing) consider the Fluke 726 Precision Multifunction Calibrator. For documenting and HART communication built into your calibrator, consider the Fluke 754 Documenting Process Calibrator with HART.   Specifications: Fluke 725 Multifunction Process Calibrator Measurement Accuracy Voltage DC 30.000 V 0.02% 2 counts (upper display) 30.000 V 0.02% 2 counts (lower display) 100.00 mV 0.02% 2 counts -10.00 mV to 75.00 mV 0.025% 1 count (via TC connector) Current DC 24.000 mA 0.02% 2 counts Resistance 0.0 to 400.0 Ω 0.1 Ω (4-wire), 0.15 Ω (2- and 3-wire) 401 to 1500 Ω 0.5 Ω (4-wire), 1 Ω (2- and 3-wire) 1500 to 3200 Ω 1 Ω (4-wire), 1.5 Ω (2- and 3-wire) Frequency 2.0 to 1000.0 CPM 0.05% 1 count 1.0 to 1100.0 Hz 0.05% 1 count 1.00 to 10.00 kHz 0.05% 1 count Sensitivity 1 V peak-to-peak-minimum Pressure Accuracy from 0.025% of range using any of 29 pressure modules (for detailed specifications refer to pressure modules in options and accessories). Modules available for differential, gauge, vacuum, absolute, dual and high pressure. Source Accuracy Voltage DC 100.00 mV 0.02% 2 counts 10.000 V 0.02% 2 counts -10.00 mV to 75.00 mV 0.025% 1 count (via TC connector) Current DC 24.000 mA (source) 0.02% 2 counts 24.000 mA (simulate) 0.02% 2 counts Resistance 15.0 to 400.0 Ω 0.15 Ω (exc. current 0.15 to 0.5 mA), 0.1 Ω (exc. current 0.5 to 2 mA) 401 to 1500 Ω 0.5 Ω (excitation current 0.05 to 0.8 mA) 1500 to 3200 Ω 1 Ω (excitation current 0.05 to 0.4 mA) Frequency 2.0 to 1000.0 CPM 0.05% 1.0 to 1100.0 Hz 0.05% 1.00 to 10.00 kHz 0.25% Waveform 5 V p-p squarewave, -0.1 V offset RTDs and Thermocouples Measure accuracy NI-120 0.2°C PT-100 (385) 0.33°C PT-100 (393) 0.3°C PT-100 (JIS) 0.3°C PT-200 (385) 0.2°C PT-500 (385) 0.3°C PT-1000 (385) 0.2°C Resolution 0.1°C J 0.7°C K 0.8°C T 0.8°C E 0.7°C R 1.8°C S 1.5°C B 1.4°C L 0.7°C U 0.75°C N 0.9°C Resolution J, K, T, E, L, N, U: 0.1°C, 0.1°F B, R, S: 1°C, 1°F XK 0.6°C BP 1.2°C Source accuracy NI-120 0.2°C PT-100 (385) 0.33°C PT-100 (393) 0.3°C PT-100 (JIS) 0.3°C PT-200 (385) 0.2°C PT-500 (385) 0.3°C PT-1000 (385) 0.2°C Resolution 0.1°C Accuracy stated for 4-wire measurement. J 0.7°C K 0.8°C T 0.8°C E 0.7°C R 1.4°C S 1.5°C B 1.4°C L 0.7°C U 0.75°C N 0.9°C Resolution J, K, T, E, L, N, U: 0.1°C, B, R, S: 1°C XK 0.6°C BP 1.2°C Specifications Ramp functions Source functions Voltage, current, resistance, frequency, temperature Ramps Slow ramp, Fast ramp, 25% step-ramp Loop power function Voltage 24 V Accuracy 10% Maximum current 22 mA, short circuit protected Step functions Source functions Voltage, current, resistance, frequency, temperature Steps 25% of range, 100% of range Environmental Specifications Operating temperature -10°C to 55°C Storage temperature -20°C to 71°C Operating altitude 3000 m Safety Specifications Agency approvals EN 61010-1:1993, ANSI/ISA S82.01-1994; CAN/CSA C22.2 No 1010.1:1992 Mechanical and General Specifications Size 130 x 236 x 61 mm Weight 0.65 kg Batteries 4 AA alkaline batteries Battery replacement Separate battery compartment, accessable without breaking calibration seal Side port connections Pressure module connector, also used for remote real-time programming